Sb-filters Cold Air Intake Kit - Cotton Filter 75-5020 Manuel d'utilisateur télécharger pdf

8/21/2008

REV-A

(909) 947-0015 PHONE • (909) 947-0603 FAX

www.sbfilters.com

INSTALLATION INSTRUCTIONS

(OVER)

S&B P/N 75-5020

2006 Ford F-150 4.6L

∗ Kit may not fit vehicles with the

following Aftermarket Parts installed.

∗ Body Lift

∗ Custom Hood

∗ Throttle Body Upgrade

∗ Throttle Body Spacer

QTY PARTS LIST QTY PARTS LIST

1 (C) Intake Tube 1 (P) 3”-3.5” step adapter

1 (O) Air Box 1 (F) # 56 Hose Clamp

1 (R) Clear Lid 1 (T) #104 Hose Clamp

1 (E) 3.725”x2.938” step adapter 2 (G) # 88 Hose Clamp

4 (I) 5/16-18 SS Screw 1 (D) # 60 Hose Clamp

4 (M) 5/16 Fender Washer 2 (B) # 8 Hose Clamp

2 (N) 5/16-18 Bolt 1 (V) # 52 Hose Clamp

2 (K) 5/16-18 Lock Nut 1 (Q) S&B Air Filter

2 (L) Rubber Spacer 1 (A) 5/8“x25” Hose

1 (J) Filter Adapter 6 (S) 10/24 SS Screws

1 (H) Oval Hump Adapter 6 (U) 10/24 SS Concave Washer

TOOLS REQUIRED

1/2” Wrench & Socket

Ratchet

5/16” Nut Driver or

Flat Blade Screwdriver

T-20 Torx wrench

(supplied with kit)

Phillips head screwdriver

Your S&B Air Filter is

factory oiled and ready

to use. Air Filter P/N

KF-1031 will require 71g

of oil for main body and

17g of oil for the top

when serviced.

1. With the ignition switched off, disconnect

the negative battery cable, use an 8mm

wrench or socket.

2. Disconnect the crank case vent line from

the driver side valve cover to the OE intake

tube and remove from vehicle.

3. Disconnect the electrical connection for

the MAF sensor at the pig tail coming from

the OE intake tube.

4. Loosen the hose clamp at the throttle body

pull out and then towards the left, pulling the

OE intake assembly out of the drivers side

inner fender.

5. Remove the OE rubber grommets from the

inner fender tray (drivers side) and relocate

the wire loom closer to the fender.

6. Install the 3” to 3.5” adapter (P) to the fender

snout on the S&B air box (O), push on as far as

it will go, it may feel loose but will secure with

#56 hose clamp (F).

7. Install the S&B air box (O) and secure

using the 5/16 bolts (N), fender washers (M),

rubber spacers (L) and lock nuts (K)

provided. See diagram below.

8. Place the S&B air filter (Q) inside S&B air

box (O). Offset flange is toward the front of

the vehicle. Snap S&B filter adapter (J) into

S&B air filter (Q) secure with #104 hose

clamp (T).

1 2 3

Résumé du contenu

Page 1 - INSTALLATION INSTRUCTIONS

8/21/2008 REV-A (909) 947-0015 PHONE • (909) 947-0603 FAX www.sbfilters.com INSTALLATION INSTRUCTIONSINSTALLATION INSTRUCTIONS (OVER) S&

Page 2 - (continued)

8/21/2008 REV-A PERFORMANCE TESTING ∗ Engage parking brake and start your engine. Listen for abnormal noises. If an air leak is detected, re-inspe

Page 3 - Kit 75-5020

8/21/2008 REV-A S&B Intake Kit 75-5020

Commentaires sur ces manuels

Pas de commentaire

Sb-filters Cold Air Intake Kit - Cotton Filter 75-5020 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Accessoires d'air Sb-filters Cold Air Intake Kit - Cotton Filter 75-5020. S&B Filters Cold Air Intake Kit - Cotton Filter 75-5020 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires d'air Sb-filters Cold Air Intake Kit - Cotton Filter 75-5020